[extream]summit24 많이 사용하는 명령어

Extream

[extream]summit24 많이 사용하는 명령어

inspitus 2007. 3. 28. 13:53

기본적으로 Default VLAN에 모든 port들이 들어있다. 먼저 이 port들을 제거 해 준다.
Summit24:1 # sh vlan
VLAN Interface[0-fdf] with name "Default" created by user
   Tagging: 802.1Q Tag 1
   IP:    Waiting for bootp reply.
   IPX: Not configured
   STPD:    Domain "s0" is not running spanning tree protocol
   Protocol: Match all unfiltered protocols.
   Qos Profile: QP1
   Ports: 25. (Number of active port=0)
Untag: 1 2 3 4 5 6 7 8 9
10 11 12 13 14 15 16 17 18 19
20 21 22 23 24 25

Summit24:2 # config default delete port all
만약 1번과 5번 port를 제거 한다면 all 부분에 1, 5라고 넣어주면 됨
1번 부터 5번 까지의 port들을 제거 한다면 1 – 5라고 넣어주면 됨

Summit24:3 # sh vlan

VLAN Interface[0-fdf] with name "Default" created by user
   Tagging: 802.1Q Tag 1
   IP:    Waiting for bootp reply.
   IPX: Not configured
   STPD:    Domain "s0" is not running spanning tree protocol
   Protocol: Match all unfiltered protocols.
   Qos Profile: QP1
   Ports: 0. (Number of active port=0)

VLAN을 creat 명령어를 사용해 만든다.
Summit24:4 # creat vlan test

만든 VLAN에 port를 추가시킨다.
Summit24:5 # config vlan test add port 1 – 4

VLAN에 IP Address를 입력한다.
Summit24:6 # conf test ipaddress 211.218.145.237/28
IP interface for VLAN test has been created.
IP address = 211.218.145.237, Netmask = 255.255.255.240.

VLAN의 IP Address를 바꾸려면 IP Address만 변경하여 위와 동일하게 하면 됨.
IP Address만 삭제할때는 unconfig vlan test ipaddress 하면 됨.

Summit24:20 # config iproute add default 211.218.145.238

Summit24:21 # sh iproute

Destination    Gateway Mtr Flags Use VLAN Origin
211.218.145.224/28 211.218.145.237 1 U 0 test Direct
127.0.0.1/8    127.0.0.1 0 U H 0 test Direct
Default Route    211.218.145.238 1 UG M    0 test Static

Total number of routes = 3.

Mask distribution:
1 default routes    1 routes at length 8
1 routes at length 28

Route origin distribution:
2 routes from Direct    1 routes from Static

장비의 Configuration을 삭제하는 방법
Summit24:8 # Unconfigure switch all
위와 같은 명령을 내리면 장비가 Configuration을 지운 후 재 부팅 함.

설정된 것이 아니라 새로 만들려는 항목들에 대한 명령어 순서는 대부분이
Create  config 순서로 이루어 진다.
Create vlan name
Config vlan name 등등의 형식

기존에 가지고 있는 항목들은 대개 enable , disable로 처리된다.
Enable route sharing
Enable ipforwording

설정에 대해 지우고 싶을때는 delete 혹은 config name delete등의 형식으로 이루어 진다.
Delete vlan name
Delete account 등의 형태를 가진다.

Interface가 10M 인지 100M인지 또는 auto로 configuration 되어 있는지 확인
Summit24:9 # sh ports 1 info

Information for port 1:
Port state: enabled
Link state: active
Port diagnostic: pass
Configured Duplex mode: auto    Actual Duplex Mode: full
Configured speed: auto Actual Speed: 100
Link up 1 time(s)
Link down 1 time(s)
Media type: UTP
Has redundant port: no
Summit Link disabled
Extreme Discovery Protocol: enabled
Qos Monitor: disabled
Load sharing is not enabled
MAC Learning: enabled
VLAN information:
test(untagged) Vlan Id: 4095

Port 의 Configuration변경방법

Summit24:10 # configure ports 1 auto off speed 100 duplex full
Summit24:11 # configure ports 1 auto off duplex full speed 100

위 2개의 명령어는1번 port를 강제적으로 100 full로 잡는 방법이다.

Summit24:12 # configure ports 1 auto on
1번 port를 auto로 잡는 방법임.

다른 장비와 연결된 port가 제대로 동작하는지 확인

Summit24:8 # Sh port stats

Port Statistics Thu Jun 19 20:41:11 2003
Port Link    Tx Pkt Tx Byte Rx Pkt Rx Byte Rx    Rx
   Status    Count    Count Count    Count Bcast Mcast
=================================================================
1 READY 0    0    0    0 0 0
2    ACTIVE    1959    244308 2880 3925901 0 0
3 READY 0    0    0    0 0 0
4 READY 0    0    0    0 0 0
5 READY 0    0    0    0 0 0
6 READY 0    0    0    0 0 0
7 READY 0    0    0    0 0 0
8 READY 0    0    0    0 0 0
9 READY 0    0    0    0 0 0
10 READY    0    0    0    0 0 0
=================================================================
   0->Clear Counters U->page up D->page down ESC->exit
Displays real-time receive error statistics.

Summit24:8 # Sh port rxerror
Port Rx Error Monitor Thu Jun 19 20:37:25 2003
Port    Link    Rx    Rx    Rx    Rx Rx    Rx    Rx
Status    CRC Over    Under Frag Jabber    Align Lost
=================================================================
1    READY    0    0    0    0    0    0    0
2 ACTIVE    0    0    0    0    0    0    0
3    READY    0    0    0    0    0    0    0
4    READY    0    0    0    0    0    0    0
5    READY    0    0    0    0    0    0    0
6    READY    0    0    0    0    0    0    0
7    READY    0    0    0    0    0    0    0
8    READY    0    0    0    0    0    0    0
9    READY    0    0    0    0    0    0    0
10    READY    0    0    0    0    0    0    0
=================================================================
   0->Clear Counters U->page up D->page down ESC->exit

Displays real-time transmit error statistics.

Summit24:8 # Sh port txerror
Port Tx Error Monitor Thu Jun 19 20:40:10 2003
Port    Link Tx    Tx    Tx    Tx    Tx
Status Coll Late Coll Deferred    Error Parity
=================================================================
1    READY    0    0    0    0    0
2 ACTIVE    0    0    0    0    0
3    READY    0    0    0    0    0
4    READY    0    0    0    0    0
5    READY    0    0    0    0    0
6    READY    0    0    0    0    0
7    READY    0    0    0    0    0
8    READY    0    0    0    0    0
9    READY    0    0    0    0    0
10    READY    0    0    0    0    0
=================================================================
   0->Clear Counters U->page up D->page down ESC->exit

Port들의 사용율을 체크 할 때 사용. ( spacebar를 사용해 다른 정보들도 볼 수 있음.)
   (packet/sec -> bytes/sec -> % bandwidth)
Summit24:6 # sh port utilization

Link Utilization Averages Thu Jun 19 20:45:11 2003
Port    Link    Receive    Peak Rx Transmit    Peak Transmit
Status packet/sec pkt/sec pkt/sec pkt/sec
=================================================================
   1 READY    0    0 0 0
   2    ACTIVE    240    240 210 210
   3 READY    0    0 0 0
   4 READY    0    0 0 0
   5 READY    0    0 0 0
   6 READY    0    0 0 0
   7 READY    0    0 0 0
   8 READY    0    0 0 0
   9 READY    0    0 0 0
10 READY    0    0 0 0

=================================================================
   spacebar->toggle screen U->page up D->page down ESC->exit

장비에 관한 대략적인 정보를 볼 수 있음.
Summit24:24 # sh switch

sysName:    Summit24
sysLocation:
sysContact: support@extremenetworks.com, +1 888 257 3000
System MAC: 00:01:30:60:85:00

License:    Basic L3.
Qos Mode: Ingress
System Mode:    802.1Q EtherType is 8100.    CardFailureAction Mode:    None
PACE disabled.    Jumbo disabled.
Current time: Wed Jul 2 13:41:21 2003
Timezone: GMT Offset: 0 minutes, DST is in effect.
Auto DST check: Enabled
Boot time:    Wed Jul 2 11:49:28 2003
Next reboot:    None scheduled
Timed upload: None scheduled
Temperature:    Normal.    All fans are operational.
Power supply: Primary OK, RPS not present

Software image selected:    primary
Software image booted:    primary
Primary software version: 4.1.21b1
Secondary software version: 4.1.15b4

Configuration selected: primary
Configuration booted: primary
Primary configuration:    444520 bytes saved on Fri Jun 13 15:02:10 2003
Secondary configuration:    444520 bytes saved on Tue Feb 4 15:07:11 2003

장비가 사용하고 있는 Boot image와 image를 확인

Summit48:15 # sh ver

System ID: 800013-14-0037M02655
Board ID: 700015-11-0037M00694
Left Board ID: 700016-10-0036M00614
Right Board ID: --
Image : Extremeware Version 4.1.19 (Build 2) by Release_Master Wed 08/09/200
0 6:09p
BootROM : 1.9